Dynare 4.5.0 installation probem

This forum is closed. You can read the posts but cannot write. We have migrated the forum to a new location where you will have to reset your password.
Forum rules
This forum is closed. You can read the posts but cannot write. We have migrated the forum to a new location (https://forum.dynare.org) where you will have to reset your password.

Dynare 4.5.0 installation probem

Postby parantap » Wed Jun 21, 2017 4:48 pm

Hi
I tried to install dynare 4.5.0. I followed all the instructions, setting path etc. When I tried to run a dynare code, it threw me off the system.

Now when I open matlab (2016a) it gives me the following warning message. I uninstalled 4.5.0 version and deleted the relevant matlab folder and went back to 4.4.3. I continue to get the same warning. How do I get rid of this warning. It looks like 4.5.0 is not working in my machine.


Warning: Directory access failure: \Users\tzha\ZhaData\Git\TZcode\MatlabFiles
> In path (line 109)
In startup (line 32)
In matlabrc (line 209)
Warning: Directory access failure:
\Users\tzha\ZhaData\Git\TZcode\MatlabFiles\MSV
> In path (line 109)
In startup (line 33)
In matlabrc (line 209)
parantap
 
Posts: 31
Joined: Tue Oct 01, 2013 11:58 pm

Re: Dynare 4.5.0 installation probem

Postby parantap » Wed Jun 21, 2017 7:19 pm

I finally set path to default and reset it to dynare 4.4.3\matlab. Now the warning message is gone. But the fact remails dynare 4.5 has installation issues.
parantap
 
Posts: 31
Joined: Tue Oct 01, 2013 11:58 pm

Re: Dynare 4.5.0 installation probem

Postby jpfeifer » Wed Jun 21, 2017 8:04 pm

The folder you mention does not seem to be a Dynare folder. What is the error you encounter with 4.5?
------------
Johannes Pfeifer
University of Cologne
https://sites.google.com/site/pfeiferecon/
jpfeifer
 
Posts: 6940
Joined: Sun Feb 21, 2010 4:02 pm
Location: Cologne, Germany

Re: Dynare 4.5.0 installation probem

Postby parantap » Wed Jun 21, 2017 9:14 pm

Dear Johannes,
I installed dynare 4.5 version in my computer. It created a folder dynare. 4.5. I added the path \dynare4.5\matlab. I saved it. I then tried to run a dynare code which runs fine in version 4.3.3. As soon as I ran it in 4.5 it ran fully but then threw me off the matlab window. I did not get any output whatsoever. Matlab just shut of on my face. Since then I started getting this error message in my matlab start up window. Very strange!!!

PB
parantap
 
Posts: 31
Joined: Tue Oct 01, 2013 11:58 pm

Re: Dynare 4.5.0 installation probem

Postby jpfeifer » Wed Jun 21, 2017 9:20 pm

Did you remove the other paths to older versions before doing this? Because the strange folder is not part of Dynare. Did you add
Code: Select all
Users\tzha\ZhaData\Git\TZcode\MatlabFiles

?
There may be a conflict here.
------------
Johannes Pfeifer
University of Cologne
https://sites.google.com/site/pfeiferecon/
jpfeifer
 
Posts: 6940
Joined: Sun Feb 21, 2010 4:02 pm
Location: Cologne, Germany

Re: Dynare 4.5.0 installation probem

Postby parantap » Wed Jun 21, 2017 9:54 pm

No I did not. I followed standard installation instruction. I thought the new path will overwrite the old path. This spunds very new. This should be written in the installation guide.
parantap
 
Posts: 31
Joined: Tue Oct 01, 2013 11:58 pm

Re: Dynare 4.5.0 installation probem

Postby jpfeifer » Fri Jun 23, 2017 10:15 am

Usually, it works that way. You are the first one to experience/report an issue like that.
------------
Johannes Pfeifer
University of Cologne
https://sites.google.com/site/pfeiferecon/
jpfeifer
 
Posts: 6940
Joined: Sun Feb 21, 2010 4:02 pm
Location: Cologne, Germany


Return to Dynare help

Who is online

Users browsing this forum: Google [Bot] and 12 guests